? 正確保養快速卡盤的方法-變位機

歡迎光臨 濟南鑫浩焊接技術有限公司官方網站!

關于我們|網站地圖|加入收藏

全國熱線: 134-5513-5688
0531-88635477
當前位置:主頁 > 資訊中心 > 行業新聞 >

正確保養快速卡盤的方法

文章出處:濟南鑫浩焊接技術有限公司關鍵詞:變位機人氣: 發表時間:2016-10-20 12:14 字體大小:【

  快速卡盤是機床等設備的的重要部件,平常要多注意保養和維護, 尤其是使用環境特殊或者包裝特殊產品時更要增加保養的頻率。下面小編帶您詳細介紹一下如何來正確保養快速卡盤,以便可以增長設備的使用壽命,提高工作生產效率。

  Quick chuck is an important part of machine tools and other equipment, usually have to pay more attention to the maintenance and maintenance, especially to increase the maintenance of special environment of special products or packaging frequency. The following Xiaobian take you to explain in detail how to properly maintain the rapid growth of chuck, to the service life of equipment, improve production efficiency.

  1、使用工作完成后必須使用風槍等工具對快速卡盤本體以及滑道表面進行清潔,這樣可以保證車床快速卡盤長時間使用之后仍具有有良好精度,所以對快速卡盤的定期潤滑工作很重要。

  1, after the completion of the work must use air gun and other tools for fast and clean the surface of the chuck body slide, which can guarantee the long time after using the fast lathe chuck has good precision, so regular lubrication is important for quick chuck.

  2、每天至少打一次二硫化鉬油脂(顏色為黑色),將油脂打入快速卡盤油嘴內直到油脂溢出夾爪面或快速卡盤內孔處(內孔保護套與連結螺帽處)。

  2, every day at least once MoS2 grease (black), the oil into the oil nozzle until the oil overflow quick chuck jaw face or quick chuck hole (hole protective sleeve connected with the screw cap).

  3、為防止快速卡盤內部生銹,加持力降低,無法夾緊工件, 因此最好使用具有防銹效果的切削油,使用切削油可以預防快速卡盤內部生銹。

  3, in order to prevent the rapid internal chuck rust, the blessing is reduced, unable to clamp the workpiece, so it is best to use cutting oil with anti rust effect, the use of cutting oil can prevent internal rust fast chuck.

  4、作業完成時必須以風槍或類似工具來清潔快速卡盤本體及滑道面。

  The air gun or similar tool to clean and fast chuck body slide surface must be 4, when work is complete.

  5、快速卡盤至少每過6個月拆下清洗,保持夾爪滑動面干凈并給予潤滑,使快速卡盤壽命增長。

  5, quick chuck at least every 6 months to remove the cleaning, keep clean and give the jaw sliding surface lubrication, the rapid growth of chuck life.

  6、檢查各部零件有無破裂及磨損之情形,削鑄鐵至少每2個月一次來徹底清潔,如遇嚴重有損零件應立刻更換新品。

  6, check the parts with no breakdown and wear of the situation, cutting cast iron at least once every 2 months to completely clean, such as the case of serious damage to the parts should be replaced immediately.

  7、針對不同工件必須使用不同夾持方式,若是使用它去夾不規則工件會造成快速卡盤損壞。

  7, according to different workpiece clamping methods must be different, if you use it to clamp the irregular workpiece will cause rapid damage to chuck.

  我們已做好準備,以全新的姿態迎接新老客戶,歡迎您來電咨詢,洽談,我們將繼續為您把好關,服好務。

  We are ready to meet new and old customers, welcome you to inquire, negotiate, we will continue to be good for you, good service.

下一篇:三維滑塊的特點 上一篇:沒有了

同類文章排行

最新資訊文章