? 正確保養卡盤的方法知識-變位機

歡迎光臨 濟南鑫浩焊接技術有限公司官方網站!

關于我們|網站地圖|加入收藏

全國熱線: 134-5513-5688
0531-88635477
當前位置:主頁 > 資訊中心 > 行業新聞 >

正確保養卡盤的方法知識

文章出處:濟南鑫浩焊接技術有限公司關鍵詞:變位機人氣: 發表時間:2016-10-20 11:32 字體大小:【

  卡盤是機床等設備的的重要部件,平常要多注意保養和維護, 尤其是使用環境特殊或者包裝特殊產品時更要增加保養的頻率。下面小編帶您詳細介紹一下如何來正確保養卡盤,以便可以增長設備的使用壽命,提高工作生產效率。

  Chuck is an important part of machine tools and other equipment, usually have to pay more attention to the maintenance and maintenance, especially to increase the maintenance of special environment of special products or packaging frequency. The following Xiaobian take you to explain in detail how to properly maintain the chuck, so as to increase the service life of equipment, improve production efficiency.

  1、使用工作完成后必須使用風槍等工具對卡盤本體以及滑道表面進行清潔,這樣可以保證車床卡盤長時間使用之后仍具有有良好精度,所以對卡盤的定期潤滑工作很重要。

  1, after the completion of the work must use air gun and other tools on the chuck body and slide surface cleaning, it can guarantee the lathe chuck is used for a long time still has good precision, so regular lubrication of the chuck is very important.

  2、每天至少打一次二硫化鉬油脂(顏色為黑色),將油脂打入卡盤油嘴內直到油脂溢出夾爪面或卡盤內孔處(內孔保護套與連結螺帽處)。

  2, every day at least once MoS2 grease (black), the grease into the nozzle until the oil overflow chuck jaw face or chuck hole (hole protective sleeve connected with the screw cap).

  3、為防止卡盤內部生銹,加持力降低,無法夾緊工件, 因此最好使用具有防銹效果的切削油,使用切削油可以預防卡盤內部生銹。

  3, to prevent the chuck body rust, the blessing is reduced, unable to clamp the workpiece, so it is best to use cutting oil with anti rust effect, the use of cutting oil can prevent internal rust chuck.

  4、作業完成時必須以風槍或類似工具來清潔卡盤本體及滑道面。

  The air gun or similar tool to clean the chuck body and slide surface must be 4, when work is complete.

  5、卡盤至少每過6個月拆下清洗,保持夾爪滑動面干凈并給予潤滑,使卡盤壽命增長。

  5, chuck at least every 6 months to remove the cleaning, keep clean and give the jaw sliding surface lubrication, the chuck life growth.

  6、檢查各部零件有無破裂及磨損之情形,削鑄鐵至少每2個月一次來徹底清潔,如遇嚴重有損零件應立刻更換新品。

  6, check the parts with no breakdown and wear of the situation, cutting cast iron at least once every 2 months to completely clean, such as the case of serious damage to the parts should be replaced immediately.

  7、針對不同工件必須使用不同夾持方式,若是使用它去夾不規則工件會造成卡盤損壞。

  7, according to different workpiece clamping methods must be different, if you use it to clamp the irregular workpiece chuck will cause damage.

  8、當卡盤壓力不正常時使卡盤處于高壓力下將工件夾住,這將會降低卡盤使用壽命。

  8, when the pressure is not normal to chuck chuck in high pressure workpiece clamped, which will reduce the service life of chuck.

  我們的反應釜質量好,價格實惠,服務周到 ,在業內一直深受新老客戶的好評與青睞,而且我們堅信在以后的經營中我們本著誠信第一的原則會越做越好!

  The reactor the quality of our good, affordable, and thoughtful service, in the industry has been highly praised and favored by the old and new customers, and we believe that in the future business in our first principle of good faith will be better!

同類文章排行

最新資訊文章